Tatung Home Theater Screen TBM 0903 User Manual

Operating Instructions  
For B/W Video Monitor  
TBM-0903 / TBM-1203 / TBM-1403  
TBM-1503 / TBM-1703 / TBM-2003  
 
FCC INFORMATION  
This equipment has been tested and found to comply with the limits for a class B  
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference in a residential installation.  
This equipment generates, uses and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause harmful  
interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or television  
reception, which can be determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of the following  
measures:  
- Reorient or relocate the receiving antenna.  
- Increase the separation between the equipment and receiver.  
- Connect the equipment into an outlet on a circuit different from that to which the  
receiver is connected.  
- Consult the dealer or an experienced radio/TV technician for help.  
Shielded interface cables and A.C. power cord, if any, must be used in order to  
comply with emission limits.  
Changes or modifications not expressly approved by the party responsible for  
compliance could void the user's authority to operate the equipment.  
SAFETY PRECAUTIONS  
1. Operate this unit only from the type of power source indicated on the label.  
2. Do not block or cover ventilation openings on the back or bottom of the monitor  
cabinet.  
3. Do not place this monitor near a radiator or heating vent.  
4. Do not push objects of any kind through cabinet openings. This may result in fire  
or electrical shock.  
5. Before adding attachments always ask a service technician to perform routine  
safety tests to determine that equipment is in safe operating condition. Ground  
potential tests should be part of the routine safety check made by the service  
technician.  
6. Do not place monitor on an unstable cart, stand, or shelf where it may fall and  
injure personnel or damage equipment.  
2
 
7. Route power cords so that they cannot be walked upon or tripped over. Do not  
allow anything to rest on the power cord.  
8. Do not install monitor in wet areas, or where it may be exposed to rain or water.  
Do not spill liquid of any kind on the unit.  
9. Unplug the power cord from the unit before cleaning the display. Use only a damp  
cloth. Do not use alcohol, spirits, or ammonia to clean the display.  
DO NOT ATTEMPT TO CLEAN THE INTERIOR OF THIS UNIT-THIS ACTION MUST  
BE PERFORMED BY THE SERVICE TECHNICIAN AS REQUIRED DURING NORMAL  
MAINTENANCE.  
10. Refer all servicing to qualified service personnel. REMOVAL OF BACK COVER BY  
UNAUTHORIZED PERSONNEL MAY EXPOSE THE USER TO DANGEROUS  
VOLTAGES OR OTHER HAZARDS.  
11. Unplug the unit immediately and notify the service technician.  
A. If liquid has been spilled into the display or the display has been exposed to  
rain or water.  
B. If the unit has been dropped or the cabined damaged.  
C. If fuses continue to blow.  
D. If the power cord is damaged or frayed.  
E. If a distinct change from normal operation is apparent.  
When replacement parts are required, be sure that the service technician Uses  
components specified by the manufacturer, which have the same characteristics as  
the original parts. Unauthorized substitutions may result in fore, electrical shock or  
other hazards.  
Upon completion of any service or repairs, ask the technician to perform safety  
check to determine that the equipment is in safe operating condition.  
Warning: Serious shock hazards exist within the covers of this monitor. Do not  
open the covers under any circumstances, there are no user  
serviceable components inside.  
3
 
GENERAL FEATURES  
1. Compatible With : EIR / CCIR  
2. Scanning System : EIR 15750 /60 Hz or CCIR 15625 / 50 Hz  
3. Input Signal : CVBS  
4. Input Power : 100~240V AC  
5. Limited twelve months warranty  
STANDARD SYSTEM COMPONENTS AND ATTACHMENTS  
Monitor  
The various components and attachments are shown below:  
TBM-1403  
TBM-1203  
TBM-0903  
TBM-1503  
TBM-1703  
TBM-2003  
4
 
TBM0903 FRONT AND REAR VIEW  
Front View :  
1. Power On/Off Switch  
2. Power-On Indicator  
3. Contrast Adjustment  
4. Brightness Adjustment  
5. H-HOLD Adjustment  
6. V-HOLD Adjustment  
7. Volume Adjustment  
TBM-0903  
Rear View  
1. Power Inlet  
2. Video Input : BNC Connector  
3. Video Output : BNC Connector  
4. Audio Input : RCA Jack  
5. Audio Output : RCA Jack  
6.Load Impedance Switch  
TBM-0903  
5
 
TBM1203 FRONT AND REAR VIEW  
Front View :  
1. Power On/Off Switch  
2. Power-On Indicator  
3. Contrast Adjustment  
4. Brightness Adjustment  
5. H-HOLD Adjustment  
6. V-HOLD Adjustment  
7. Volume Adjustment  
TBM-1203  
Rear View  
1. Power Inlet  
2. Video Input : BNC Connector  
3. Video Output : BNC Connector  
4. Audio Input : RCA Jack  
5. Audio Output : RCA Jack  
6.Load Impedance Switch  
TBM-1203  
6
 
TBM1403 FRONT AND REAR VIEW  
Front View :  
1. Power On/Off Switch  
2. Power-On Indicator  
3. Contrast Adjustment  
4. Brightness Adjustment  
5. H-HOLD Adjustment  
6. V-HOLD Adjustment  
7. Volume Adjustment  
TBM-1403  
Rear View  
1. Power Inlet  
2. Video Input : BNC Connector  
3. Video Output : BNC Connector  
4. Audio Input : RCA Jack  
5. Audio Output : RCA Jack  
6.Load Impedance Switch  
TBM-1403  
7
 
TBM1503 FRONT AND REAR VIEW  
Front View :  
1. Power On/Off Switch  
2. Power-On Indicator  
3. Contrast Adjustment  
4. Brightness Adjustment  
5. H-HOLD Adjustment  
6. V-HOLD Adjustment  
7. Volume Adjustment  
TBM-1503  
Rear View  
1. Power Inlet  
2. Video Input : BNC Connector  
3. Video Output : BNC Connector  
4. Audio Input : RCA Jack  
5. Audio Output : RCA Jack  
6.Load Impedance Switch  
TBM-1503  
8
 
TBM1703 FRONT AND REAR VIEW  
Front View :  
1. Power On/Off Switch  
2. Power-On Indicator  
3. Contrast Adjustment  
4. Brightness Adjustment  
5. H-HOLD Adjustment  
6. V-HOLD Adjustment  
7. Volume Adjustment  
8. Video input Select Switch  
9. Audio input Select Switch  
TBM-1703  
Rear View  
1. Power Inlet  
2. Video 1 Load Impedance Switch  
3. Video 2 Load Impedance Switch  
4. Video 1 Input : BNC Connector  
5. Video 1 Output : BNC Connector  
6. Video 2 Input : BNC Connector  
7. Video 2 Output : BNC Connector  
8. Audio 1 Input : RCA Jack  
9. Audio 1 Output : RCA Jack  
10. Audio 2 Input : RCA Jack  
11. Audio 2 Output : RCA Jack  
TBM-1703  
9
 
TBM2003 FRONT AND REAR VIEW  
Front View :  
1. Power On/Off Switch  
2. Power-On Indicator  
3. Contrast Adjustment  
4. Brightness Adjustment  
5. H-HOLD Adjustment  
6. V-HOLD Adjustment  
7. Volume Adjustment  
8. Video input Select Switch  
9. Audio input Select Switch  
10. Over/under-scan Select Switch  
TBM-2003  
Rear View  
1. Power Inlet  
2. Video 1 Load Impedance Switch  
3. Video 2 Load Impedance Switch  
4. Video 1 Input : BNC Connector  
5. Video 1 Output : BNC Connector  
6. Video 2 Input : BNC Connector  
7. Video 2 Output : BNC Connector  
8. Audio 1 Input : RCA Jack  
9. Audio 1 Output : RCA Jack  
10. Audio 2 Input : RCA Jack  
11. Audio 2 Output : RCA Jack  
TBM-2003  
10  
 
OPERATION  
OPERATING INSTRUCTIONS  
1. Place the monitor where you plan to use it.  
2. This monitor can be operated between 100VAC to 240VAC.  
3. Plug the power cord into AC RECEPTACLE on the wall.  
4. Link the A/V terminal from your devices into the audio / video in (RC A / BNC)  
Connectors of the monitor.  
5. Turn your device system power switch ON. then turn the monitor power switch ON.  
The power indicator will be ON at this moment.  
6. Allow about 30 seconds for the display tube to warm up, then the image of the  
Display should appear on the screen,and power -ON LED indicator luminant.  
7. The monitor will detect the frequency of the input signal automatically, and the  
Display image is able to be adjusted through the function VR on front control panel.  
11  
 
TATUNG COMPANY OF AMERICA  
2850 EL PRESIDIO ST.  
LONG BEACH,CA 90810  
3121-0097G02  
 

Technicolor Thomson CRT Television DF 421 C User Manual
Toshiba Cash Register MA 132 SERIES User Manual
Toshiba Satellite TV System 1405 User Manual
Troy Bilt Lawn Mower 769 06304 User Manual
Uniden Cell Phone MHS 350 User Manual
Uniden Cordless Telephone EXI 6960 User Manual
Uniden Cordless Telephone TRU9260 Series User Manual
Uniden Cordless Telephone TRU9465 User Manual
Victor Technology Calculator 909 User Manual
VTech Cordless Telephone mi6861 User Manual