T
P
S
2
1
5
1
P
o
w
e
r
M
a
n
a
g
e
m
e
n
t
W
i
t
h
L
D
O
a
n
d
D
u
a
l
Ć
C
u
r
r
e
n
t
Ć
L
i
m
i
t
e
d
P
o
w
e
r
S
w
i
t
c
h
E
v
a
l
u
a
t
i
o
n
M
o
d
u
l
e
User’s Guide
March 2002
PMP Portable Power
SLVU067
EVM IMPORTANT NOTICE
Texas Instruments (TI) provides the enclosed product(s) under the following conditions:
This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION
PURPOSES ONLY and is not considered by TI to be fit for commercial use. As such, the goods being provided
may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective
considerations, including product safety measures typically found in the end product incorporating the goods.
As a prototype, this product does not fall within the scope of the European Union directive on electromagnetic
compatibility and therefore may not meet the technical requirements of the directive.
Should this evaluation kit not meet the specifications indicated in the EVM User’s Guide, the kit may be returned
within 30 days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE
WARRANTY MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED,
IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user
indemnifies TI from all claims arising from the handling or use of the goods. Please be aware that the products
received may not be regulatory compliant or agency certified (FCC, UL, CE, etc.). Due to the open construction
of the product, it is the user’s responsibility to take any and all appropriate precautions with regard to electrostatic
discharge.
EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE
TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not
exclusive.
TI assumes no liability for applications assistance, customer product design, software performance, or
infringement of patents or services described herein.
Please read the EVM User’s Guide and, specifically, the EVM Warnings and Restrictions notice in the EVM
User’s Guide prior to handling the product. This notice contains important safety information about temperatures
and voltages. For further safety concerns, please contact the TI application engineer.
Persons handling the product must have electronics training and observe good laboratory practice standards.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any
machine, process, or combination in which such TI products or services might be or are used.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright 2002, Texas Instruments Incorporated
EVM WARNINGS AND RESTRICTIONS
It is important to operate this EVM within the specified input and output ranges described in
the EVM User’s Guide.
Exceeding the specified input range may cause unexpected operation and/or irreversible
damage to the EVM. If there are questions concerning the input range, please contact a TI
field representative prior to connecting the input power.
Applying loads outside of the specified output range may result in unintended operation and/or
possible permanent damage to the EVM. Please consult the EVM User’s Guide prior to
connecting any load to the EVM output. If there is uncertainty as to the load specification,
please contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than
60°C. The EVM is designed to operate properly with certain components above 60°C as long
as the input and output ranges are maintained. These components include but are not limited
to linear regulators, switching transistors, pass transistors, and current sense resistors. These
types of devices can be identified using the EVM schematic located in the EVM User’s Guide.
When placing measurement probes near these devices during operation, please be aware
that these devices may be very warm to the touch.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright 2002, Texas Instruments Incorporated
Preface
Read This First
About This Manual
The TPS2151 is one of the four devices in the USB peripheral power
management family TPS2140/41/50/51, which integrates both an adjustable
linear low-drop voltage regulator (LDO) and a dual-current-limited power
switch. The dual-current-limit power switch is designed to eliminate inrush
current during power on.
The evaluation module (EVM) can help designers to evaluate the device with
several different configurations by manipulating only a couple of onboard
mechanical slide switches and a few jumpers.
Users need at least one dc voltage supply and a multimeter or oscilloscope to
evaluate the operation of the EVM.
How to Use This Manual
This document contains the following chapters:
- Chapter 1—Introduction
- Chapter 2—Schematic, Bill of Materials, Layout, and Setup
- Chapter 3—Changeable Components and Test Points
v
Information About Cautions and Warnings
Information About Cautions and Warnings
This book may contain cautions and warnings.
This is an example of a caution statement.
A caution statement describes a situation that could potentially
damage your software or equipment.
This is an example of a warning statement.
A warning statement describes a situation that could potentially
cause harm to you.
The information in a caution or a warning is provided for your protection.
Please read each caution and warning carefully.
vi
Contents
1
2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Schematic, Bill of Materials, Layout, and Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.1
2.2
2.3
2.4
Schematic of the EVM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Layout of the EVM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Setup of the EVM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
3
Changeable Components and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Figures
2–1
2–2
Schematic of the TPS2151 Evaluation Module (EVM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Top Layer of the EVM and Placement of the Components . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Tables
2–1
3–1
Bill of Materials of the TPS2151 EVM (SLVP202) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Test Points and Test Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
vii
viii
Chapter 1
Introduction
Each device in TPS2140/41/50/51 family integrates a dual-current-limiting
power switch and an adjustable low dropout regulator (LDO). Both the switch
and LDO limit inrush current by controlling the turnon slew rate and are
compatible with USB 1.0 and 2.0 Specifications.
The power switch has a unique dual-current-limiting function that limits the
current delivered to its load to less than 100 mA during power on. This feature
allows the load to utilize high-value capacitance at the output of the switch,
while keeping the inrush current low. When the output voltage from the switch
reaches about 93% of the input voltage, the switch power good output goes
high, and the switch current limit increases to 800 mA (minimum), at which
point higher current loads can be turned on. Therefore the load, other than
capacitance, on the switch output must not exceed the lower current limit (50
mA minimum) before the power good output rises to high.
Designers may activate the load by using either the power good signal or
another logic signal. The higher current limit provides short circuit protection
while allowing the load to draw maximum current from the source.
The switch and LDO function independently provides flexibility in many
applications requiring separate core and I/O voltages.
TPS2151 has a 5-V switch and an active high /SW_EN that distinguishes itself
from the other three parts (TPS2140, TPS2141, and TPS2150). For a detailed
description of functions and characteristics of the TPS2140/41/50/51, refer to
the data sheet (literature number SLVS399). You may check the data sheet
and ordering information on the Web site:
TPS2151
To assist designers in the evaluation of the device, an evaluation module
(SLVP202) is offered based on TPS2151. The EVM requires 5-V supplies for
both the power switch and the LDO. The LDO output voltage is set to 3.3 V by
an external resistor divider. Two slide switches and few jumpers on the EVM
are provided to change the connections between the LDO and the power
switch, so several different application configurations can be evaluated.
The required external parts for the EVM are two input capacitors (on SW_IN
and LDO_IN), three output capacitors (on SW_OUT and LDO_OUT), and a
resistor divider (two resistors). All of these components are placed inside a
white-rectangle box on the EVM.
1-1
1-2
Chapter 2
Schematic, Bill of Materials, Layout, and Setup
This chapter contains schematics, bill of materials, board layout, and setup of
EVM.
Topic
Page
2.1 Schematic of the EVM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.2 Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
2.3 Layout of the EVM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
2.4 Setup of the EVM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
2-1
Schematic of the EVM
2.1 Schematic of the EVM
Figure 2–1 shows the schematic of the EVM.
Figure 2–1. Schematic of the TPS2151 Evaluation Module (EVM)
2-2
Schematic of the EVM
Only C2, C4, C5, C6, C8, R2, and R3 are essential for the TPS2151 to function
properly. The rest of the components on the EVM are used for different
evaluations of the device. To evaluate the power switch inrush current, a large
capacitor C9 can be added on the EVM.
In order to discharge SW_OUT and LDO_OUT quickly, JP4 and JP5 are
shorted through jumpers on this EVM. Designers may unplug the jumpers and
find the difference. Based on the schematic, the following configurations can
be set by switches (S1 and S2), and jumpers on JP1, JP2, and JP3:
1) Independent operation between the switch and LDO: JP1, JP2, and JP3
are floating (no jumpers). In this configuration, header J1 inputs control the
switch and the LDO, and the device outputs are connected to header J2.
External loads for the switch and the LDO are connected to J2. SW_IN and
LDO_IN are powered by a single supply through J1 or by separate
supplies.
2) Another independent operation: only JP1 is floating (no jumper). A jumper
shorts JP2 from LDO_EN pin to S1 pin, and JP3 is shorted from SW_EN
to S2. In this configuration, slide switches S1 and S2 control the switch and
the LDO. No external control signals are connected to SW_EN and
LDO_EN on header J1. This configuration makes the evaluation easier by
sliding the switches S1 and S2 to control the TPS2151 on and off. SW_IN
and LDO_IN are powered by a single supply through J1, or by separate
supplies.
3) LDO power good to control the power switch: JP1 is still floating, but JP3
is shorted from SW_EN to LDO_PG (no external input SW_EN allowed on
J1) JP2 can be configured the same as either case 1) or case 2). The
power switch of TPS2151 is controlled by the LDO power good output
LDO_PG. The power switch cannot be turned on until the LDO is fully on.
SW_IN and LDO_IN are powered by a single supply through J1 or by
separate supplies.
4) Switch power good to control the LDO: JP1 is still floating, but JP2 is
shorted from LDO_EN to SW_PG (no external input LDO_EN allowed on
J1). JP3 can be configured the same as either case 1) or case 2). Then
the LDO of TPS2151 is controlled by the switch power good output
SW_PG. So the LDO cannot be turned on until the power switch is fully
on. SW_IN and LDO_IN are powered by a single supply through J1 or by
separate supplies.
5) Switch feeding power to the LDO: JP1 is shorted, and JP2 is shorted from
LDO_EN to SW_PG (no external input LDO_EN allowed on J1). JP3 can
be configured the same as either case 1) or case 2). Then the LDO is
connected to the power switch output and controlled by the switch power
good SW_PG. Only one supply is needed for SW_IN through J1, and no
external supply is allowed on LDO_IN at J1.
6) Other configurations can be constructed by further manipulating the
jumpers, slide switches and the input and output headers (J1 and J2).
Schematic, Bill of Materials, Layout, and Setup
2-3
Bill of Materials
Warning
Users must not activate the load on SW_OUT before the SW_PG
rises to high, if the load current is higher than 50 mA. Otherwise,
the power switch output could not be charged up to SW_IN rail.
2.2 Bill of Materials
The bill of materials (BOM) for the EVM is shown in Table 2–1.
Table 2–1.Bill of Materials of the TPS2151 EVM (SLVP202)
Count RefDes
Description
Size
MFR
Panasonic 29D475X0010B2T
Kemet C0805C104KRAC7800
Part Number
3
4
C1, C3, C6
Capacitor, Tantalum, 4 µF, 10 V, 20%
B Case
805
C2, C4, C5, C8 Capacitor, ceramic 0.1 µF, 50 V, X7R
10%
0
C7
Note: Needed only if the LDO voltage
is set to be below 3 V, refer to the data
sheet
0
2
C9
Note: Extra high-value capacitor on
SW_OUT
J1, J2
Header, 8 pin, 100 mil spacing, (36-pin 0.100 x 8”
Sullins
PTC36SAAN
strip)
0
3
2
2
1
2
J3
Connector, USB downstream (Type A)
Header, 2 pin, 100 mil spacing
0.52 x 0.57”
0.100 x 2”
0.100 x 3”
805
Molex
Sullins
Sullins
Std
87531–001
PTC36SAAN
PTC36SAAN
Std
JP1, JP4, JP5
JP2, JP3
R1, R3
R2
Header, 3 pin, 100 mil spacing
Resistor, chip, 200 KΩ, 1/10 W, 5%
Resistor, chip, 625 kΩ, 1/10 W, 5%
805
Std
Std
S1, S2
Switch, 1P2T, slide, PC-mount,
200 mA
0.46 x 0.16”
E_Switch
EG1218
5
0
TP1, TP2,
TP3, TP4, TP9
Test point, black, 1 mm
0.038”
Farnell
240–333
TP16, TP17,
TP18, TP19,
TP20, TP21
Post, wire wrap, 0.043 press-fit
Note: A/A
0.015–0.025” Mill-Max
pins
1045–3–17–15–30–14–
02–0
11
TP5, TP6,
TP7, TP8,
TP10, TP11,
TP12, TP13,
TP14, TP15,
TP22
Test point, red, 1 mm
0.038”,
Farnell
240–345
0
1
TR1
Note: Paralleling with R2 to set LDO
output voltage lower than 3.3 V
U1
IC, USB high powered, with LDO
PWP14
TI
TPS2151PWP
2-4
Layout of the EVM
2.3 Layout of the EVM
Figure 2–2 illustrates the placement of the components on the top-layer of the
TPS2151 EVM. All the components are placed on the top layer only. The
bottom layer is mainly a ground plane except for a few short traces. The center
rectangle box includes all the essential parts for the EVM.
Figure 2–2. Top Layer of the EVM and Placement of the Components
Schematic, Bill of Materials, Layout, and Setup
2-5
Layout of the EVM
2.4 Setup of the EVM
For proper operation of the EVM, please follow these steps for any evaluation:
1) Verify that the power supply voltages are in the required ranges: less than
5.5 V but higher than 4.1 V. Make sure the supplies have the capability to
supply the current that the loads need. Turn off the supplies.
2) In order to discharge SW_OUT and LDO_OUT quickly, JP4 and JP5 are
shorted through jumpers on this EVM. Designers may unplug the jumpers
and find out the difference. Set one of the six configurations as explained
in section 2.1. Then connect one or two supplies to the EVM through J1.
3) Connect loads to the outputs (between SW_OUT and GND, and between
LDO_OUT and GND) through J2 if required. However, users can test a
number of characteristics of the controller without external loads.
If users need to evaluate the dual-current limit for large output capacitance, a
surface-mount D-size cap footprint is provided (C9) for that purpose. Or, you
may connect the cap from SW_OUT to GND at J1.
The LDO output on the EVM is preset to 3.3V by resistor R2 and R3. If a lower
output is required, either R2 can be replaced with a lower resistance resistor,
or add an appropriate resistor on TR1 footprint. Refer to the data sheet to get
the correct resistance value.
4) Turn on and turn off the power switch and LDO based on the configuration
you choose.
5) Test points are provided for oscilloscope probes and/or multimeters.
2-6
Chapter 3
Changeable Components and Test Points
C1, C2, C3, C4—input capacitors, at least 0.047µF total on each input.
C5, C6, C8, C9—load capacitors, vary according to loads, but C5 plus C6 must
be at least 4.7 µF.
R2—top resistor of the resistor divider, refer to data sheet for its resistance
value.
R1—LDO_PG pullup resistor, must be at least 1kΩ.
A total of 16 test points are provided. Besides four black test points on the four
corners of the EVM, there are 12 more test points (11 red and 1 black) residing
on two sides of the white rectangle box at the center of the EVM. Their
respective testing signals are listed in the following table, when looking at the
EVM from top down. The test-point orders are listed from top to bottom on both
sides.
Table 3–1.Test Points and Test Signals
Left-side
Right-side
Test-Point Order
Color
Red
Signal
Test-Point Order
Color
Red
Red
Red
Red
Red
Red
Signal
1
2
3
4
5
6
SW_PG
SW_IN
LDO_IN
SW_EN
LDO_EN
GND
1
2
3
4
5
6
SW_PLDN
SW_OUT
LDO_OUT
LDO_PLDN
ADJ
Red
Red
Red
Red
Black
LDO_PG
3-1
3-2
|