Verbatim MP3 Player VM 01 User Manual

Store ‘n’ Play  
MP3 Player  
USERꢀMANUALꢀVM-01  
 
Table of Contents  
Play mode.......................................................................................................23  
System setting................................................................................................24  
Sleep.........................................................................................................24  
Sleep memory ..........................................................................................24  
Scrolling speed.........................................................................................25  
Contrast....................................................................................................26  
Backlight time..........................................................................................26  
User interface language............................................................................27  
Restore default setting..............................................................................28  
Version .....................................................................................................28  
Stand-by time...........................................................................................28  
Appendix........................................................................................................29  
Trouble shooting ............................................................................................30  
Specifications of product................................................................................32  
Technical support & warranty........................................................................33  
 
FCC Notice  
FCC Notice:  
This equipment has been tested and found to comply with the limits for a  
Class B digital device, pursuant to part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection against harmful interference  
in a residential installation. This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio and  
television reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the interference by one or more  
of the following measures:  
- Reorient or relocate the receiving antenna.  
- Increase the separation between the equipment and receiver.  
- Connect the equipment into an outlet on a circuit different from that to which  
the receiver is connected.  
- Consult the dealer or an experienced radio/ TV technician for help.  
CE Notice:  
If the product suddenly has no response or power off, it may be caused by  
electrostatic discharge. If this circumstance, please follow the procedures  
below for recovery:  
- Switch off the unit, if the unit has no response.  
- Turn on the unit again  
For Customers in Europe  
This product conforms to the following European Directives:  
89/336/EEC (EMC Directive)  
This product complies with EN55022/A1:2000 and EN 55024/A1:2001 for use  
in the following areas: residential, commercial and light industrial  
 
Handling Precaution  
Before using this device, please carefully read and understand the safety  
instructions listed below.  
1. Read carefully all the attached user’s materials, and fully understand the  
operation guide and warnings of this device.  
2. Check if the contents in the packaging of the device are consistent to the  
packing list.  
3. When it is left unused for a long period of time, the battery should  
be removed. If liquid leakage from the battery is detected and  
the device works abnormally, please do not dismantle the device for  
cleaning, this may lead to damage to the device. In irreparable cases,  
please contact Verbatim technical support. Verbatim shall take no liability  
for damages resulting from battery liquid leakage and resulting damage.  
4. This device is a hi-tech electronic product, which should be kept away  
from heat, cold and moisture when being used. Special care should be taken  
to observe the following points:  
a) The device should not be exposed to strong sunlight, and should be kept  
away from heat sources.  
b) Avoid using the device outdoor at low temperature for a long period  
of time.  
c) The device should not be placed in the environment of extra-humidity;  
Care should be taken so that water and other liquids are not spilled onto  
the device. If it happens, the device should be switched off immediately.  
d) The device should not be used in dusty environments.  
e) Do not clean the device with any type of detergent containing chemical  
elements or other solutions in order to avoid damage from corrosion or  
moisture. If necessary, please clean using a soft cloth.  
5. Do not use the device in strong magnetic field, strong electric charge or  
electromagnetic interference environment in order to prevent data from  
being lost.  
 
Handling Precaution  
6. Do not subject the device to drops or hard impacts which may lead to  
damage.  
7. The device should be opened under no circumstances. The manufacturer  
takes no liability for damages resulting from unauthorized tampering.  
 
Product Features  
- Supports WMA and MP3 file formats  
- Bit rates supported 32kbps - 320kbps constant & variable  
- Windows Media DRM 9 support  
- Negative LCD Display with LED back light  
- ID3 Tag: Song title and Artist  
- Voice recorder with built in microphone  
- 6 EQ modes: Normal, Rock, Jazz, Classic, Pop & Custom  
- 5 Play modes: Normal, Repeat, Repeat all, Shuffle, & Repeat Shuffle  
- Preset sleep timings  
- Sleep memory function  
(restart resumes to where the device was last powered off)  
- Built in USB plug to connect directly to the PC  
- USB2.0 Full speed data transfer  
- Compatible with USB1.1 & USB2.0 ports  
- 1 x AAA battery  
-
Battery life up to 10 hours  
 
Package Contents  
1. Store ‘n’ Play MP3 Player VM-01 (x1)  
2. Stereo Earphones  
3. USB Extension Cable  
4. AAA Battery  
5. Carry Strap  
6. Quick Start Guide  
7. CD containing Win 98SE driver and Users Manuals  
 
Product Diagrams and Function Buttons  
Earphone jack  
MIC jack  
Play/pause button  
A-B Repeat section  
Volume +  
Fast forward button  
Menu button  
Fast backward button  
Volume -  
Lock button  
USB jack  
Battery Housing  
LCD display screen description  
A-B Repeat section display  
Playing mode display  
EQ display  
Volume level display  
Song name  
Sleep preset display  
Function button lock display  
Mode display  
Playing status display  
Play elapsed time display  
Song playing display  
 
Product Diagrams and Function Buttons  
Operating method  
Battery installation  
 
ꢀ0  
Product Diagrams and Function Buttons  
 
ꢀꢀ  
Product Diagrams and Function Buttons  
 
ꢀꢁ  
Connecting to the Computer  
Computer system requirement  
1. Microsoft Windows 98SE/Me/2000/XP  
2. CD-ROM drive  
3. Pentium CPU above 233MHz  
4. With RAM memory above 32MB(if the operating system is Windows XP,  
the RAM should be above 64MB)  
5. Hard disk space should be above 20MB  
6. Port should be USB1.1 or above  
7. Connecting to internet (necessary only when the software needs  
to be updated)  
 
ꢀꢂ  
USB Connection Display  
This player is a mass storage device. It does not need driver installation for  
PC connection. However for windows 98SE OS you need to install the driver.  
The driver is contained on the enclosed CD or download the driver from the  
For USB connection,the device can be plugged in the USB port of the  
computer, Press “Play/Pause” button to connect.  
When the device is connected to computer, and the operation begins, LCD will  
display the following icon  
USB connected  
files uploading  
files downloading  
 
ꢀꢃ  
File Upload and Download  
After the device is connected to the computer to upload/download files, no  
special operation other than simple “drag-drop” is needed.  
1. Double click “my computer” in Windows, you will find a new  
icon “removable disk”, which represents your digital audio player  
2. If you want to download files to the device from computer, just drag the  
desired files to “removable disk”, which represents your digital audio player  
3. You can also drag the files in your digital audio player to your computer  
(upload)  
4. The device can store all types of files in addition to music files.  
5. During uploading / downloading, keep the MP3 player connected to  
the computer  
Notes:  
1. Since the device will play according to the download sequence of the files, it  
is suggested to download files in desired sequence.  
2. To disconnect from the USB port Double-Click the “Unplug or Eject  
Hardware” symbol in the Windows task bar. When the “Safely Remove  
Hardware” window appears, select the device you wish to remove and click  
stop. From the next window, select the appropriate device and click ok.  
The MP3 player is now ready to disconnect.  
3. During uploading / downloading, keep the MP3 player connected to  
the computer  
 
ꢀꢄ  
An Introduction to Basic Functions  
Power on/off  
Power on  
Press “play/pause” button to start the device  
Start figure  
The following picture (figure) has been set in the device before it left factory.  
Power off  
1. Long press “play” button, the device will be shut down, as the progress bar  
displayed below.  
2. When the progress bar is full, the device will be shut down automatically.  
3. If releasing the “play” button before the progress bar is full, the device will  
resume to the former status. Designed in this way, the device will not be shut  
down accidentally.  
Shutting downÖ  
 
ꢀꢅ  
An Introduction to Basic Functions  
Volume setting  
Adjust the volume by using “VOL+”and” VOL-” on the main device  
1. Volume can be selected among 0-10 sections.  
2. Press the button to adjust the volume section by section; long press on the  
button to adjust the volume continuously.  
Mode switch  
This device has two working modes: music mode and voice mode.  
Press and Hold MENU to enter mode selecting menu, and then select desired  
mode by using “fast forward “button or “fast backward” button or select “exit”  
to keep the original mode, press “MENU” button again to enter that mode.  
 
ꢀꢆ  
An Introduction to Basic Functions  
Mode menu setting  
Music (music mode), voice (voice mode) or exit (keep the mode selected  
before) are available.  
menu setting in music mode  
menu setting in voice mode  
 
ꢀꢇ  
An Introduction to Basic Functions  
Lock function  
When switching on “HOLD” lock button, all the functions cannot be operated.  
Switch on the device when it is shut down, “locked” will be displayed. When it  
is playing, there will be an icon of “locked” on the upper right of LCD.  
Play music  
Play/pause  
The device will enter music mode or voice mode when it is normally started,  
press “play/pause” button to begin playing; when it is playing, press “play/  
pause”  
button to pause playing; The file is in STOP status when the device is normally  
started.  
1. Select play file  
1) When it is pause/stop, press “fast forward” button or “fast backward”  
button to select files in the memory.  
2) When it is playing, press “fast forward” button to play the next file, while  
press “fast backward” button to play the previous file  
2. Fast forward/fast backward  
Press “fast forward” button or “fast backward” button for more than one  
second to begin fast forward or fast backward.  
 
ꢀꢈ  
An Introduction to Basic Functions  
Voice record  
In voice mode, you can record voice via the built-in Mic  
1) Press “Rec/A-B” button to begin recording  
2) Press “Rec/A-B” button again to stop recording  
3) Recorded files are stored as default files VXXX.WAV, XXX, begins with 001  
Play record  
Voice files recorded in the device can be played in voice mode. The  
operation is identical to playing music files in music mode.  
 
ꢁ0  
An Introduction to Additional Functions  
Repeat section (A-B)  
When music file or voice file is being played, press REC/A-B button to set the  
start point (point A) for repetition, and press REC/A-B button again to set the  
ending point (point B). The device will begin repeat the section. Press  
REC/A-B button again to cancel A-B playing the current file.  
EQ setting  
EQ selection: “normal, rock, jazz, classic, pop, custom” are available.  
In custom mode, there are 4 grades of high keys and 4 grades of low  
keys available. You can also select “exit” to keep the original settings.  
 
ꢁꢀ  
File Management  
Delete  
1. Press “MENU” button to enter function menu, Select “Delete” with “fast  
forward” button or “fast backward” button.  
2. Press “MENU” button to enter delete function;  
3. Search for the files by using “fast forward” or “fast backward” button,  
and select “yes” to delete the files; select “no” to return to the menu.  
4. When the message “file deleted” is displayed on LCD, press “fast  
forward” button to select “exit” and return to main menu.  
Delete mode selection menu  
Formatting  
When the device is connected to computer, it will be displayed as “removable  
disk” in Windows” of my computer”. Click the icon with the right key, and  
select formatting in the spring-out menu. The device can be formatted as  
computer magnetic disk.  
Notes: 1.When formatting the removable disk representing your digital audio  
player, please select FAT16/32 format for file partition system.  
2. If FAT16/32 format is not selected for file partition system, the  
device cannot be started normally. In this case, please connect the  
device to the computer and format it into FAT16/32, and it will  
resume normal working.  
 
ꢁꢁ  
Firmware Upgrade  
Firmware upgrade file and upgrade procedures are available from the  
below websites:  
You are recommended to check the availability of new firmware release  
versions to perform upgrades periodically to enhance the performance of  
the player.  
Notes:  
1. Disconnection during firmware upgrading may cause failure to the device.  
2. Do not change the file name or extensions of the uploaded files.  
 
ꢁꢂ  
Play Mode  
Normal: play all the music files one by one and stop  
Repeat one: play the current music file, and repeat playing it  
Repeat all: play all music files one by one, and repeat them all  
Random: Randomly play all the music files once and stop  
Repeat Random: Randomly play all the music files ,and repeat again  
Exit: keep the play mode selected originally.  
 
ꢁꢃ  
System Setting  
System setting selection menu  
In the modes of music or voice, the following system settings are included.  
Sleep  
To preset auto sleep time. The device will shut down automatically and  
accordingly after the selected minutes. “Off, 15, 30, 45, 60” minutes are  
available. You can also select “exit” to keep the original settings.  
 
ꢁꢄ  
System Setting  
Resume  
If the sleep memory is set to “YES” , the status information will be recorded  
when the player is shut down. When it starts again, the player resumes to  
the status last time it was shut down;If the sleep memory is set to “NO” ,  
the status will not be recorded when the player is shut down, when it starts  
again, the player will get into default status. You can also select “exit” to  
keep the original settings.  
Scroll speed  
If the length of character string is too long to be displayed, LCD will  
scroll the character string display. The speed of scroll can be selected among  
“off, slow, moderate, and fast. You can also select “exit” to keep the original  
settings  
 
ꢁꢅ  
System Setting  
Contrast  
To set the contrast of LCD, totally 10 grades: “1,2,3,4,5,6,7,8,9,10” are  
available. You can also select “exit” to keep the original settings.  
Backlight time  
To set the time of LCD backlight for each operation, “off, 10 seconds,  
30 seconds, 60 seconds, permanent” are available.  
You can also select “exit” to keep the original settings.  
 
ꢁꢆ  
System Setting  
User Interface Languages:  
English, France, Spanish, Portuguese, German, Italy are available.  
 
ꢁꢇ  
System Setting  
Restore default setting  
If selecting “yes”, the MP3 player will resume the default setting. If selecting  
“no”, or “exit”, the player keeps the current setting.  
Version  
It is used to display the version of the firmware of the device.  
IDLE time  
To set the stand-by time. When the MP3 player in stand-by status reaches  
the preset stand-by time, the MP3 player automatically shut down to save  
energy. There are “off, 3, 5” minutes of stand-by time available. You can also  
select “exit” to keep the original settings.  
 
ꢁꢈ  
Appendix  
A list of menus  
Normal  
Repeat one  
Repeat all  
Random  
Play mode  
Repeat randon  
Normal  
Rock  
Jazz  
EQ  
MENU  
Classic  
Pop  
User  
Delete  
Setting  
Sleep  
Resume  
Scrolling speed  
Contrast  
Backlight time  
backlight time  
OSD languages  
Default  
Version  
version  
IDLE time  
standby time  
 
ꢂ0  
Trouble Shooting  
1. The device fails to work or LCD does not display.  
1) Check if there is enough battery power.  
2) Check if the polarities of battery are correct.  
2. The device does not respond to button press.  
1) Check if the “hold” button is in “ON” position.  
2) If it is in “OFF” position, button press does not work.  
3. It can not play MP3 files.  
1) Check if there is a MP3 file in the memory.  
2) Check if the player is in music mode.  
4. It can not play voice files.  
1) Check if there is a voice file in the memory.  
2) Check if the player is in voice mode.  
5. A-B Repeat section fails.  
1) This function only works when a music or voice file is being played.  
6. After the device is connected to computer, there is player icon on  
the computer.  
1) Make sure that the driver program has been correctly installed, and  
the player is powered on. Connect USB plug correctly to the computer.  
Make sure that the device has been correctly installed by checking  
the “device manager” of the computer.  
 
ꢂꢀ  
Trouble Shooting  
7. How to restore the default setting of the player.  
1) Select “restore default setting” in the system setting of the device, and select  
“yes” to restore the default setting.  
8. LCD backlight is not on.  
1) Check if the backlight setting in the system setting of the device is set in  
“OFF” position.  
 
ꢂꢁ  
Specification of Product  
Dimensions (L x W x H)  
Net weight  
85 x 26 x 22mm  
34g (battery not included)  
128/ 256/512MB/1GB (depending on product version)  
One alkaline battery 1.5V AAA  
Built-in USB plug  
Memory  
Power supply  
PC interface  
Play  
MP3, WMA, support VBR  
ADPCM (32Kbps)  
Digital voice format  
Build-in Mic  
Capacitive Mic  
Signal-to-noise ratio  
Range of audio frequency  
Play mode  
Larger than 85dB  
20Hz-20KHz  
Normal, Repeat one, Repeat all, Shuffle, Repeat shuffle  
Up to 10 hours  
Batttery life  
Notes: The above-mentioned specifications of digital audio player are subject  
to further modification for the purpose of performance upgrading without  
special Notes.  
 
ꢂꢂ  
Technical Support  
Europe: For technical support in Europe e-mail  
[email protected] or call 00 800 3883 2222 in the following  
countries: Austria, Belgium, Denmark, Finland, France, Germany, Hungary,  
Italy, Luxembourg, Monaco, Netherlands, Norway, Poland, Portugal, Republic  
of Ireland, Spain, Sweden and Switzerland.  
All other countries call +353 61 226586  
US/Canada: For technical support in the U.S. and Canada email  
[email protected] or call 800-538-8589.  
Verbatim Limited Warranty:  
Verbatim Corporation warrants this product to be free from defects in material  
and workmanship for a period of 1 year from date of purchase (a period of 2  
years applies in countries in the European Union). This warranty excludes bat-  
teries. If this product is found to be defective within the warranty period, it will  
be replaced at no cost to you. You may return it with your original cash register  
receipt to the place of purchase or contact Verbatim.  
In the U.S and Canada, call 800-538-8589 or email [email protected]  
In the following European counties Austria, Belgium, Denmark, Finland,  
France, Germany, Hungary, Italy, Luxembourg, Monaco, Netherlands, Norway,  
Poland, Portugal, Republic of Ireland, Spain, Sweden and Switzerland call  
00 800 3883 2222. All other European countries call +353 61 226586. You can  
Product replacement is your sole remedy under this warranty, and this warranty  
 
ꢂꢃ  
Technical Support  
does not apply to normal wear or to damage resulting from abnormal use,  
misuse, abuse, neglect or accident or to any incompatibility or poor  
performance due to the specific computer software or hardware used.  
VERBATIM WILL NOT BE LIABLE FOR DATA LOSS OR ANY  
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, HOWEVER  
CAUSED, FOR BREACH OF WARRANTIES OR OTHERWISE.  
This warranty gives you specific legal rights and you may also have  
other rights which vary from state to state or country to country.  
NOTE: Verbatim Corporation may at any time revise the content of this user  
guide without further notice.  
 

Technicolor Thomson Universal Remote 28DT68L User Manual
Toastmaster Coffeemaker ME5CB User Manual
Toastmaster Convection Oven 7091W User Manual
Toshiba Projector MP8640 User Manual
Triarch Indoor Furnishings 29272 User Manual
Tripp Lite Surge Protector SPS415HGULTRA User Manual
ViewSonic Projector PJD5112 User Manual
Viking Cooktop F20562D User Manual
Viking Cooktop VGSU103 4B User Manual
VisionTek Modem 81GC User Manual