Viking Computer Hardware 366D User Manual

Viking Memory  
I N S T A L L A T I O N G U I D E  
ACER®  
4. Locate the single memory expansion slot  
in the open compartment. Also locate the  
off-center key on the slot. There will be a  
standard memory module occupying the  
expansion slot.  
Extensa 365 Series (Model 367T, 367D, 366D)  
5. In order to upgrade your system past 32MB of memory, its standard  
memory module will need to be removed. To remove a memory module,  
locate the retaining clips on both sides of the memory module. Gently  
pull both clips away from the module and then lift the module out of its  
expansion slot.  
Manual No. 1005246 • Release 07/98, Rev. A  
S P E E D  
P O W E R  
P E R F O R M A N C E  
The Acer Extensa 365 Series (Model 367T, 367D, 366D) comes stan-  
dard with 32MB (16MB soldered + 16MB module) of memory. It can be  
expanded to a maximum of 80MB* by installing the following Viking  
Components memory options into its one available expansion slot.  
Description  
Viking P/N  
16MB SDRAM Memory Module  
32MB SDRAM Memory Module  
64MB SDRAM Memory Module  
AC80420, RAC80420  
AC80421, RAC80421  
AC80422, RAC80422  
6. To install a memory module, insert the module into an expansion slot  
at an angle and then push it down until it clicks into place. To be certain  
that the module is installed correctly, ensure that the off-center notch on  
the module is aligned with the off-center key of the expansion slot. The  
module can only be installed one way due to the position of the notch.  
*Requires the removal of the standard memory module.  
Caution:  
Electro Static Discharge (ESD) can damage electronic components. Before  
touching the memory module, ensure that you are discharged of static elec-  
tricity by touching a grounded metal object.  
INSTALLATION INSTRUCTIONS:  
1. Turn the computer off and disconnect the AC power supply and any  
other cables from the unit.  
7. Replace the memory expansion cover back to its original position and  
be sure to secure its three holding screws.  
Note: If the unit appears to be powered down, ensure that it is not in  
Suspend mode.  
8. Insert the battery back into its compartment and turn the system right-  
side up.  
9. Replace the AC power supply and any other cables you may have dis-  
connected.  
2. Turn the computer upside-down. Remove  
the battery from the system. If you are not  
familiar with this procedure, please refer to  
your computer’s “Owners Manual.”  
10. Open the display screen and turn the system on. The computer will  
automatically reconfigure itself to recognize the additional memory. The  
new memory can be verified during the POST routine at start-up and at  
the SETUP utility.  
3. Facing the front of the computer, locate  
the memory expansion cover on the right-  
side of the bottom panel. Also locate the  
three holding screws on the left-side of this  
cover. Remove only these three screws with  
a small Phillips-head screwdriver. Then  
remove the cover by lifting it up.  
The installation is now complete.  
Copyright 1998 Viking Components, Inc.  
 

Tech4o Watch CW1 User Manual
Texas Instruments Network Card TMS320DM36X User Manual
Toshiba Laptop 81 User Manual
Toshiba Network Card VR Series User Manual
Toshiba Portable Generator VF S11 User Manual
Uniden Two Way Radio GMRS540 User Manual
Velodyne Acoustics Speaker Digital Drive Subwoofer User Manual
ViewSonic Flat Panel Television VA1938w LED User Manual
Vivotek Security Camera IP8336W User Manual
Wayne Water Pump 350800 002 User Manual