Wagner SprayTech Microwave Oven MCS 425 User Manual

MCS-425 Microwave sensor switch  
Installation Instruction  
How to use  
1.Before turning-on this unit, please make sure all cables are  
connected properly.  
2.The mounting height is 230 cm.  
3.Antenna angle (D) is adjustable, the higher the antenna angle,  
the wider the detection range that can be detected. Instead, the  
lower the antenna angle, the narrower the detection range that  
can be detected.  
4.Turn the (A) clockwise to increase the antenna detection range,  
or the counter-clockwise turn to decrease the antenna detection  
range.  
Jumper  
+ AC/DC 12~24V  
-
N.C  
Com.  
N.O.  
N.C.  
N.O.  
A
C
D
5.Turn the (C) clockwise to increase the relay actuation time, or  
the counter-clockwise turn to decrease the relay actuation time.  
LED  
A
C
Clockwise turns on switch to is biggest.  
Clockwise turns on switch to increase the  
relay actuation time. (0.5 ~ 4 Seconds)  
Relay mode and Jumper Status  
The factory settings  
No power  
Relay Statue  
Detects the signal  
Relay Action Status  
Microwave Antenna stand angel: 35°  
Jumper: N.O. (Normal open)  
Adjustment resistance:  
(A) Clockwise turns on switch to is  
biggest.  
Jumper mode  
Relay Normal Status  
N.O.=OPEN  
N.C.=CLOSED  
LED OFF  
N.O.=CLOSED  
N.C.=OPEN  
N.O.=OPEN  
N.C.=CLOSED  
LED OFF  
N.O.  
LED ON  
(C) Clockwise turns on switch to  
increase the relay actuation time.  
Detection Range: 4.5 meter  
N.O.=CLOSED  
N.C.=OPEN  
N.O.=OPEN  
N.C.=CLOSED  
N.O.=OPEN  
N.C.=CLOSED  
N.C.  
LED ON  
LED OFF  
LED OFF  
Specifications  
Power Input: 12 V~24V AC/DC (self-regulating)  
Maximum current: 80 mA  
Frequency: 10.525 GHz  
Relay actuation time: 0.5 ~ 4 Seconds  
Sensor Angle: 7.5° ~ 82.5°  
Operating Temperature Range: -20°C ~ +55°C  
Dimensions: 122.5(W) * 72(H) * 63 (D)mm  
Relay rated 3A, 125VAC / 30VDC  
Application  
MCS-425 microwave sensor switch can be used with access control system which it can work as a request to exit.  
The diagrams below illustrate the two recommended ways of installing the MCS-425 and access control devices after power input  
(power on).  
Fig. B The connection for fail-secure Lock devices  
Fig. A The connection for fail-safe Lock devices:  
Jumper(N.C.)  
Power Supply  
Jumper(N.C.)  
Power Supply  
+
+
N.C.  
N.C.  
-
N.C  
-
N.C  
Com.  
N.O.  
Com.  
N.O.  
Locking Device  
(fail-secure)  
Locking Device  
(fail-safe)  
Control Device  
Control Device  
N.C  
Com.  
N.O.  
N.C  
Com.  
N.O.  
Relay output  
control  
Relay output  
control  
Copyright © 2008 Gianni industries, inc. All rights reserved.  
P-MU-MCS-425 Ver. C Published on 2008.08.20  
 

Tascam Music Mixer DM 3200 User Manual
Toshiba Digital Photo Frame F700 User Manual
TP Link Network Router TL SG3210 User Manual
TRENDnet Security Camera Pan Tilt Internet Camera Server User Manual
Tripp Lite Switch B116 A03 User Manual
Uniden Cordless Telephone EXS9600 User Manual
Uniden Cordless Telephone XC3510 User Manual
ViewSonic Flat Panel Television VS10576 1E User Manual
Weber Gas Grill 55159 User Manual
Weber Gas Grill genesis silver b natural gas grill User Manual